Acquaponica.Shop

Guide · 7 November 2026 · 7 min read

Root rot in hydroponics: how to save the plants

Brown, mushy roots? Here’s how to identify root rot (Pythium), what to do immediately to save your plants, and how to prevent it from coming back.

Marciume radicale nelle piante in idroponica: come fare e perché e come salvare la pianta

Root rot in hydroponics is identified by brown, soft, and often foul-smelling roots instead of white, firm ones; to save the plants, you must act immediately: remove them from the system, rinse the roots, cut away the rotten parts, empty and disinfect the system, and start over with a fresh solution, cool water (ideally between 18 and 22 °C), and plenty of oxygen. If the roots are still partly white, the plants have a good chance of recovering.

The best-known culprit is Pythium, a fungus-like organism that thrives in warm, oxygen-poor water. It is not your fault or the fault of the system itself: it is the result of conditions that can be corrected. Here we show you how to recognize it, what to do in the first few hours, and how to prevent it from returning. For an overview of systems and their requirements, see the guide on hydroponic systems compared.

In short

  • Healthy roots: white or cream-colored, firm, with a neutral smell. Diseased roots: brown, slimy, falling apart at the touch, and foul-smelling.
  • The main causes are water that is too warm, insufficient oxygen, light on the reservoir, and poor hygiene.
  • Immediately: isolate the plants, rinse them, cut away the rot, empty and disinfect the system, and restore a fresh solution.
  • Prevention: cool water, strong aeration, an opaque reservoir with a lid, and cleaning during every change.
  • If more than half of the root system is rotten, saving it is difficult: it is better to start over with healthy seedlings.

How to recognize root rot

Symptoms on the leaves appear last and can be misleading: wilting during the hot hours that does not go away with water, stunted growth, and yellowing leaves. The real sign is below. Pull out a plant and look at the roots.

Appearance Healthy root Root with rot
Color White or cream (it may be slightly yellowed depending on the nutrients) Brown, gray, or black
Texture Firm, flexible Soft, slimy, slips off
Smell Neutral or like clean water Rotten, like eggs, or like stale wet earth
Root hairs Dense and vigorous Sparse or absent
Reservoir water Clear Cloudy, with filaments or foam

Beware of false alarms: light brown roots caused by the pigments of some fertilizers or by the growing medium are not rotten, as long as they remain firm and odorless. Root rot is identified by its soft texture and smell.

Why it develops: the causes

Water temperature that is too high

Above 24–25 °C, Pythium finds ideal conditions and spreads quickly; at the same time, warm water holds less oxygen. For most crops, the goal is a solution temperature between approximately 18 and 22 °C. In summer, a reservoir in the shade and underground, or a refrigerator, makes a huge difference.

Insufficient dissolved oxygen

Roots breathe. With little dissolved oxygen, they weaken, die, and become food for pathogens. The risk is greater in DWC systems and in large reservoirs with little aeration. A dedicated test, such as the dissolved oxygen test, gives an idea of the situation.

Light on the reservoir and hygiene

Light in the reservoir promotes algae, which consume oxygen at night and create organic matter on which pathogens proliferate. Dead root residue, fallen leaves, and biofilm in the pipes complete the picture. A system that is never cleaned is an ideal breeding ground.

Stressed plants from the start

A solution that is too concentrated (high EC), a pH outside the range, or already weak seedlings make the roots more vulnerable. Healthy plants in cool, well-oxygenated water are much more resistant.

What to do immediately: the rescue plan

  1. Remove the plants from the system and place them in a bucket with clean, cool water.
  2. Rinse the roots gently, without rubbing, to remove the soft material.
  3. Cut away the rotten parts with clean scissors, disinfecting them between each plant. Leave only white, firm roots; if none remain, the plant cannot be saved.
  4. Empty the reservoir and clean the bottom, channels, pipes, pumps, and porous stones thoroughly, removing the biofilm with a brush and hot water.
  5. Disinfect with a suitable product, following the label, then rinse many times with clean water until all residue is removed.
  6. Prepare a new solution with the correct EC and pH for the crop, using cool water.
  7. Reinsert the plants and increase aeration. During the first few days, reduce the EC slightly if the roots are severely reduced, so as not to stress them.

For leafy crops, the reference values are those in the Plant Manual: for example, lettuce at pH 5.5–6.0 and EC 1.2–1.8, basil at pH 5.5–6.5 and EC 1.0–1.6.

After the rescue: how to help recovery

In the following days, check the color and smell of the roots, the water temperature, pH, and EC every day. Avoid over-fertilizing: a plant with few roots absorbs very little. Some products, such as root stimulants (Canna Rhizotonic) or enzymes (Canna Cannazym), can help the growth of new roots or the cleaning of the growing medium, but they do not replace oxygen, cool water, and hygiene: they are a support, not a cure.

How to prevent it

Oxygenate more

Good aeration is the first line of defense. A large reservoir requires a suitable pump, such as the Hailea ET40, and porous stones that produce fine bubbles; for small DWC pots, smaller pumps are sufficient, such as the ACO 2201. If you are looking for something else, there is the aerators and air compressors category.

Keep the water cool

Insulate the reservoir from heat, keep it away from direct sunlight, and use a refrigerator where necessary. In recirculating systems, the pump also heats the water: choose a suitable size, without excess.

Opaque reservoir with a lid

A container that does not let light through reduces algae and heating. A tub with a lid is a simple solution; other options are in the containers and reservoirs category.

Hygiene and regular changes

Clean during every solution change, remove fallen leaves immediately, and disinfect tools when moving from a diseased plant to a healthy one. In larger systems, a UV sterilizer can also reduce the pathogen load in the circulating water, but it does not replace cleaning.

Errors to avoid

  • Waiting: root rot spreads quickly, especially in warm water. It is better to intervene at the first symptoms.
  • Treating only the plants and leaving the system dirty: the pathogen remains in the water and the pipes.
  • Using disinfectants in excess without rinsing: the residue burns the new roots.
  • Increasing the fertilizer thinking you are “feeding” the plant: with reduced roots, a high EC is an additional stress.
  • Ignoring summer: during the hot months, daily monitoring of the reservoir temperature is necessary.

Frequently asked questions

Can a plant with brown roots be saved?

It depends on how extensive the damage is. If white, firm roots remain, cutting away the rot and starting over with clean water can allow the plant to recover. If almost everything is rotten, it is more realistic to start over with a new seedling.

Can root rot spread from one plant to another?

Yes, in recirculating systems, the water carries the pathogen everywhere. For this reason, it is best to treat the entire system, even if only a few plants show symptoms.

Can I eat the affected plants?

If the above-ground parts are healthy, you can consume them after washing them thoroughly, but a plant with rotten roots is weak and yields little. Discard the soft or foul-smelling parts.

Does root rot also occur in aquaponics?

Yes, for the same reasons: warm water and insufficient oxygen. In aquaponics, you cannot use disinfectants lightly, because they harm fish and bacteria. Work on keeping temperature, aeration, and the biofilter in balance.

How often should I clean the reservoir?

At least during every complete solution change, usually every one to three weeks depending on the size. If you see biofilm, cloudiness, or odors, clean it sooner.

If you are not sure it is root rot, you can send a photo of the plant to the site chat assistant.

From theory to numbers

Continue with the tools

All tools