Guide · 12 November 2024 · 9 min read
LED lights for hydroponics: how much light do you really need
PPFD, DLI, hours of light, distance, and efficiency in µmol/J: the recommended values for leafy greens, herbs, and fruiting vegetables, and how to choose the right lamp.

For most leafy crops and herbs, you need about 200–400 µmol/m²/s of PPFD on the leaves for 14–16 hours a day, while fruiting vegetables like tomatoes and chili peppers need more, approximately 400–600 µmol/m²/s. The number that really counts is not the lamp's wattage, but how much useful light reaches the plant: it is measured in PPFD, summed up over the course of the day in DLI, and evaluated by comparing the lamp's efficiency in µmol/J.
When growing at home, in a closet or in a room without windows, light is the factor most often underestimated: water and nutrients can be corrected in a few minutes, but insufficient light results in stretched, pale, and slow-growing plants. In this guide, we look at how to think with the right units of measurement, what indicative values to use for different crops, at what distance to hang the lamp, and how to choose an LED without being guided solely by the stated power.
In short
- Look at the PPFD (light reaching the leaves, in µmol/m²/s) and not the wattage: two 100 W lamps can perform very differently.
- The DLI is the total light for the day: PPFD × hours × 0.0036. Leaves need less than fruiting vegetables.
- Indicative values: leaves 200–300 µmol/m²/s, herbs 200–400, fruiting vegetables 400–600 or more, microgreens 100–250.
- A good modern LED is around 2.5–3.0 µmol/J: this is the figure to compare between different lamps.
- The distance is adjusted using the manufacturer's PPFD map and the plants' behavior, not by eye.
- Always use a timer: nighttime darkness is part of the cycle, not a flaw.
PPFD, PAR, DLI: the three acronyms to understand
PAR is the part of the spectrum that the plant uses for photosynthesis, roughly between 400 and 700 nanometers. Lux, which is the unit for household light bulbs, is calibrated for the human eye and favors green-yellow: it says little about plants. This is why PPFD is used, which is the number of PAR photons falling on one square meter every second (µmol/m²/s).
PPFD is an instantaneous value. DLI (Daily Light Integral) is the sum of the light received in one day, in mol/m²/day. The formula is simple:
DLI = PPFD × hours of light × 3600 ÷ 1,000,000, i.e., PPFD × hours × 0.0036.
Example: 250 µmol/m²/s for 16 hours gives about 14.4 mol/m²/day, a value suitable for lettuce. The same 250 µmol/m²/s for 8 hours gives only 7.2: the plant will grow, but much more slowly. Lengthening the photoperiod and increasing the intensity are two ways to achieve the same goal, with different limits: beyond a certain number of hours, many plants gain nothing, beyond a certain PPFD, the light becomes a stress.
How much light each type of crop needs
The values in the table are indicative and based on what is commonly used in indoor growing. They vary with variety, temperature, CO₂, and nutrient availability: if the rest of the system is not in balance, more light is not needed.
| Crop type | Indicative PPFD (µmol/m²/s) | Hours of light | Indicative DLI (mol/m²/day) |
|---|---|---|---|
| Microgreens (after the dark phase) | 100–250 | 12–16 | about 6–12 |
| Leaves: lettuce, arugula, spinach | 200–300 | 14–16 | about 12–17 |
| Herbs: basil, mint, parsley | 200–400 | 14–16 | about 12–20 |
| Fruiting vegetables: tomato, chili pepper | 400–600 and more | 14–16 | about 20–30 |
Basil is a good example of a crop that loves light: it reacts well to high intensities, provided the temperature remains under control. Lettuce, on the other hand, if pushed too hard, can burn the edges of the inner leaves (tipburn), a problem often linked to strong light, little air circulation, and calcium that does not reach where it is needed.
Hours of light and photoperiod
Almost all the crops we are interested in here (leaves, herbs, tomatoes, chili peppers) do not depend on the length of the day to flower: you can keep them with 14–16 hours of light and 8–10 of darkness. Darkness is not wasted time: at night the plant moves the sugars produced during the day and breathes. Leaving the light on 24 hours a day is not a shortcut, because it usually stresses the leaves and makes them consume more energy without clear advantages.
Practical rule: if you want more DLI, first increase the intensity a little (if the plant can handle it), then add hours. All with a timer, so that the schedule is always the same: plants tolerate irregular shut-offs poorly.
Distance from the lamp
Light intensity drops very quickly as you move away from the source: with a panel lamp, doubling the distance reduces the PPFD by much more than half at the center of the beam, and the beam itself widens. This is why the right distance depends on the lamp: always look at the PPFD map that the manufacturer indicates at different heights and for different cultivation area sizes.
Some practical rules valid for any lamp:
- Start at the height recommended by the manufacturer and observe the plants for a few days.
- Plants that stretch towards the light, long internodes, pale color: too little light, lower the lamp or increase the intensity if it is dimmable.
- Whitened leaves, burned or curled edges downwards right under the lamp: too much light or too much heat, raise the lamp.
- If you can, measure. A dedicated PPFD meter is the only reliable tool; smartphone apps are approximate and should only be understood as an order of magnitude.
Also remember uniformity: a larger lamp, hung a little higher, illuminates more evenly than a small one very close. In vertical towers, the lower and upper levels receive very different light if the source is single: this must be taken into account from the beginning. For periodic checks of light, timers, and the pump, there is the tower maintenance guide.
Efficiency in µmol/J: how to compare lamps
Efficiency says how many micromoles of PAR photons the lamp produces for every joule of electrical energy absorbed (µmol/J). The higher it is, the more useful light you get from the same bill and the less heat you have to dissipate. Good modern LEDs for growing are approximately between 2.5 and 3.0 µmol/J; older or cheaper lamps drop below 2.0.
A concrete way to use the figure: multiply the absorbed power by the efficiency. A 150 W lamp with 2.7 µmol/J emits a total of about 405 µmol/s of photons; dividing by the illuminated area gives the average PPFD. On 0.5 m², it would be just over 800 µmol/m²/s in theory, but in practice, the light is not distributed evenly and some is lost at the edges, so the average value on the plants is lower. The calculation is used to understand if a lamp is oversized or insufficient for your space, not to replace measurement.
Be wary of stated wattage without efficiency data: it often indicates the power of the LEDs, not the absorbed power, or the theoretical maximum. The reliable figure is the PPFD measured at a certain distance and over a certain area.
How to choose the lamp
- Spectrum. For vegetative growth, a complete, white spectrum is perfect, with a good amount of red and a little blue. Blue keeps the plants compact; red boosts growth.
- Area to cover. Start with the actual growing surface, then choose the number of lamps to achieve the target PPFD evenly.
- Shape. Thin bars are good for shelves and towers; panels for grow boxes and tents; models with an IP65 protection rating are more suitable for humid environments.
- Heat. LEDs produce less heat than old lamps, but in an enclosed space ventilation is still needed. Heat raises the temperature and changes the VPD.
- Dimmer. Being able to adjust the intensity helps with seedlings and young transplants, which want less light than adults.
In the catalog you will find the lighting and LED category with lamps of different wattages, such as the Ortoled 150 W (2.7 µmol/J) and the 240 W model, the LED Bucaneve 120 W IP65 and the Lumatek VF 120 W bar designed for vertical farming. If you grow in a dedicated closet, also look at the grow box and tents category.
Common light mistakes
| Symptom | Probable cause | What to do |
|---|---|---|
| Long, thin plants, light green | Insufficient or too distant light | Move the lamp closer or add hours, check the PPFD |
| Dry, whitened leaf edges under the lamp | Too intense light or high temperature | Raise the lamp, reduce intensity, increase ventilation |
| Lettuce with burned inner edges | Strong light, little air circulation, immobile calcium | Reduce light, increase air movement |
| One part of the system grows, the other does not | Unevenly distributed light | Rotate the plants or change the lamp position |
| Flowers fall, few fruits | DLI too low for a fruiting vegetable | Increase intensity and hours within the variety limits |
If you are not sure what you see on the leaves, before changing the lamp, also recheck pH and nutrients: a nutrient deficiency is easily confused with a light problem. If you are starting from scratch, the home hydroponic garden guide helps you set up the entire system consistently.
New in the store: the new modular vertical hydroponic tower with 24 or 28 spots, with a 40-liter tank in three colors (white, green, or black), pump and tubes included. It is designed and printed in Italy in polypropylene suitable for food use; each module retains a reserve of solution, so the roots remain submerged even if the pump stops for a while, and it can be expanded up to 32 spots.
Frequently asked questions
Can I use a normal white LED light bulb?
For germinating a few seeds or keeping an herb on the windowsill it may be enough, but generally the PPFD reaching the plants is too low for decent growth. For regular cultivation, lamps designed for plants, with stated PPFD, are needed.
How long should I leave the light on?
For leaves, herbs, tomatoes, and chili peppers, 14–16 hours a day are generally used, with continuous darkness for the rest. There is no need to keep it on 24 hours.
How do I calculate the DLI if I don't have a meter?
Take the PPFD from the lamp's data sheet at the distance you use and apply the formula PPFD × hours × 0.0036. It is an estimate: a meter will give you the real value on the leaves.
Do LEDs hurt the eyes?
Growing lamps are very bright: avoid staring at them up close and, if you have lights with a lot of blue or red, use suitable glasses when working under them for a long time.
Is a powerful lamp far away or a less powerful one close by better?
A more powerful and higher lamp generally gives more even light; a weaker and closer one concentrates the light in the center. Always compare the PPFD maps for your area. If you don't know what is wrong, you can send a photo of the plant to the site chat assistant.
From theory to numbers
Continue with the tools
- Consumption calculatorEstimate energy, water and nutrients before you buy.Open
- System sizerStart from your space and build your system configuration.Open
- Nemo AIAsk our soilless-growing assistant a question.Open


